KraftMaid Kitchen Remodeling Nationwide

KraftMaid Kitchen Remodeling: The Santa Clarita Owner’s Guide

KraftMaid kitchen remodeling in Santa Clarita typically runs $14,000 – $45,000 installed, depending on cabinet count, finish line, and whether we’re matching existing KraftMaid pieces or starting fresh. We stock KraftMaid hinges, drawer glides, door bumpers, and shelf clips on the truck, and we can source drawer boxes, door fronts, and cabinet boxes directly through our KraftMaid supply chain. Most owners first notice a drawer that won’t close flush or a door that sags by an eighth of an inch and catches the frame. That small change usually means a hinge plate has worn or a glide has finally given out after years of daily use.

Call (661) 542-4056

Which KraftMaid Models This Applies To

We work on KraftMaid’s full catalog, including the standard overlay line, the Vantage series with its taller cabinet boxes, and the Kemper line for those in Valencia or Bridgeport who bought homes with the upgraded trim package. The fastest way to identify your exact cabinet is to pull out the bottom drawer and look for the KraftMaid stamp on the drawer box side, usually near the dovetail joint. That stamp gives us the cabinet line, the finish code, and the manufacture date, which tells us whether your hinges are the older concealed style or the newer soft-close hardware. For homeowners who want to keep their existing KraftMaid boxes but refresh the fronts, we match the finish code through our KraftMaid dealer account rather than guessing by eye, because KraftMaid’s maple, cherry, and oak finishes shift slightly between production years. Aftermarket hinges and glides work fine in most KraftMaid cabinets if the overlay measurement matches, but soft-close hardware from a generic brand rarely holds adjustment as well as the OEM KraftMaid hinges on a door that gets opened forty times a day.

Signs Your KraftMaid Kitchen Remodeling Is Failing

• Drawer won’t stay closed or slides crooked. The nylon roller on the side-mounted glide has worn flat on one side. This is the most common KraftMaid failure we see in Santa Clarita, where dry air and hard water from Castaic Lake make plastic rollers brittle faster than coastal homes.
• Door catches the frame or rubs the adjacent door. The hinge plate has loosened from the face frame, usually because the original screws were over-tightened at the factory. Once the plate wobbles, the door shifts and starts wearing the finish off the edge.
• Soft-close door slams instead of easing shut. The small piston inside the KraftMaid soft-close hinge has leaked its fluid. Once that happens, the hinge has to be replaced, not adjusted.
• Shelf dips in the middle. The shelf clips have bent or the shelf itself has absorbed moisture from years of steam and spills. KraftMaid’s standard shelves are ¾-inch plywood with a laminate skin; once the laminate edge delaminates near the sink, the shelf starts to bow.
• Finish peeling at the drawer pull or kick plate. The thermofoil or painted finish has lifted along a high-touch edge. This is more common in homes with hard water and high mineral content in the air, which describes most of the Santa Clarita Valley.

Replacement Cost & What’s Included

A full KraftMaid kitchen remodel in Santa Clarita lands between $14,000 and $45,000. A smaller galley kitchen with stock KraftMaid cabinets and a laminate countertop starts near $9,000 – $20,000, while a Bridgeport or Castaic kitchen with Vantage cabinets, a Cambria or Silestone countertop, and a larger island can push toward the top of that range. What drives cost: cabinet line and finish, whether we’re keeping existing boxes and replacing fronts only versus tearing out to the studs, countertop material, and whether the sink base needs repair from past water exposure. Every bid we write includes the parts, the labor, the haul-away, the shoe covers, the drop cloths, and a photo of the clean-up before the crew leaves. We give a written price before any work starts, and the 365-Day Done Right Promise covers every completed remodel. If a hinge we installed fails at month eleven, we’re back out to make it right.

DIY or Call Us?

If your drawer is rubbing, you can safely try adjusting the glide screws with a Phillips head. If the door is sagging, you can tighten the hinge plate screws yourself, but if the plate is stripped or the soft-close piston is dead, the hinge needs replacing and the door has to come off. That’s where a lot of homeowners get hurt, not from the hinge itself but from holding a heavy door overhead while trying to line up new screws, especially in kitchens with cathedral cabinets near the ceiling. We carry KraftMaid-compatible hinge plates, glides, bumpers, and clips on the truck, so most single-cabinet repairs happen in one visit. For anything bigger than one hinge or one glide, call us at (661) 542-4056 and we’ll give you a straight answer on what it takes.